Hardeman Motorsport - motorsport parts and diff specialist

Setting M10 Timing + tuning Weber 32/34 DMTL

Post Reply
Reck
E21 Pro
Posts: 779
Joined: Mon Mar 29, 2010 12:26 am
My E21(s): 83 316, 1.8 M10, RHD
Location: Manchester, UK

Setting M10 Timing + tuning Weber 32/34 DMTL

Post by Reck » Mon Jul 29, 2013 8:18 pm

Just did this and I thought it would be good to write it down for anyone interested.

Get the engine to operating temp before doing anything.

First, tuning the Weber;

1. Screw mixture screw all the way in. The screw is 'hidden' - see diagram below. You'll need a flathead to turn it. It'll probably have stalled by now if you still had the engine running.
2. Screw it back out two and a half turns. Restart.
3. Adjust idle screw until idling at about 900rpm.
4. Tighten mixture screw back in slowly until at 800rpm.
5. Take it to a rolling road so they can set it up properly with a sniffer and the right jets if still not good!

Idle screw:

Image

Mixture screw:

Image

Second, timing;

1. Loosen pinch bolt on distributor until the dizzy can be turned (but not so loose it needs no resistance to turn!).
2. Remove vacuum pipe(s) from dizzy and block off with a bolt.
3. Hook up your timing light according to instructions.
4. Start engine and adjust idle to screw until it sits at about 2200rpm. This is easier with a timing gun that shows RPM, otherwise expect to run back and forth from the engine bay to the dash RPM counter.
5. Point gun into timing hole (this is like an oblong cutout near where the gearbox meets the engine, if looking straight down from above the engine).
4. Slowly turn dizzy until the mark (a shiny ball bearing set into the flywheel) is visible in the middle of the hole. There's supposed to be a 'Z' near the ball too but I couldn't see this, probably due to grime.
5. Adjust idle screw again until it sits at 2200rpm again, then recheck the mark.
6. Continue doing one then the other until 2200rpm and the mark is visible and steady. Tighten distributor pinch bolt back up.
7. Turn idle screw back to 800rpm.
8. Reconnect vaccuum hoses.



User avatar
Jeroen
Site Admin
Posts: 25023
Joined: Tue Sep 14, 2004 12:23 pm
My E21(s): '81 323i Baur
Location: The Netherlands
Contact:

Re: Setting M10 Timing + tuning Weber 32/34 DMTL

Post by Jeroen » Tue Jul 30, 2013 12:20 am

Thanks for this useful writeup mate!
Regards/groeten, Jeroen

We want your contributions in our E21 Facebook Group! Join, like, post & share!

User avatar
mcjjordan
Upcoming E21 fanatic
Posts: 197
Joined: Fri Jul 12, 2013 9:55 pm
My E21(s): Uk 1980 316 m52
Location: eastleigh/southampton in Hampshire , England
Contact:

Re: Setting M10 Timing + tuning Weber 32/34 DMTL

Post by mcjjordan » Mon Aug 26, 2013 3:31 pm

does timing need adjusting after fitting weber then?
as was good with the pierburg

Reck
E21 Pro
Posts: 779
Joined: Mon Mar 29, 2010 12:26 am
My E21(s): 83 316, 1.8 M10, RHD
Location: Manchester, UK

Re: Setting M10 Timing + tuning Weber 32/34 DMTL

Post by Reck » Tue Aug 27, 2013 12:48 pm

Not necessarily - it's good practice to set timing occasionally though. Might aswell do it at the same time so you feel the whole benefit of the new carb (increased power!). :-)

User avatar
mcjjordan
Upcoming E21 fanatic
Posts: 197
Joined: Fri Jul 12, 2013 9:55 pm
My E21(s): Uk 1980 316 m52
Location: eastleigh/southampton in Hampshire , England
Contact:

Re: Setting M10 Timing + tuning Weber 32/34 DMTL

Post by mcjjordan » Fri Sep 27, 2013 10:38 pm

cheers

Post Reply