The Rust Rocket, 2.5i convertion

Share the story on your car, and photos!
Post Reply
User avatar
Millar
Upcoming E21 fanatic
Posts: 196
Joined: Fri Jun 11, 2010 8:46 pm
Location: Scottish Borders

Post by Millar »

thanks for that, will make patching a lot easier knowing what to use! :)


User avatar
Millar
Upcoming E21 fanatic
Posts: 196
Joined: Fri Jun 11, 2010 8:46 pm
Location: Scottish Borders

Post by Millar »

So started the exhaust build today, got about is far as cutting the back box off then spent the rest of my time figuring out how i'd put it together, and in what configuration. In the end i decided i couldn't be bothered with the hassle of having a pipe at either side of the car, as it looked like it would just get ripped off if i bottomed out, which you do a lot on my roads! So instead i got the hacksaw out and turned it into a double exhaust where the original used to be. Should look pretty good, i'm hoping anyway. Just waiting for some u-bolt clamps and some sealant to arrive so i can finish up.
Biggest problem with the kit, bar my lack of patience, is that the clamps that come with it are too big, they don't go nearly tight enough to hold it all together.

The car sounds amazing with just the back box cut off! If its not too loud, the middle box is coming out too.
User avatar
e21-Mark
E21 Master
Posts: 5715
Joined: Fri Mar 21, 2008 2:19 pm
My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
Facebook page: https://www.facebook.com/JackyardBackoff
Location: Cornwall - UK

Post by e21-Mark »

On my old 320, we removed the centre box and went with a single silencer iirc.

Image
User avatar
Millar
Upcoming E21 fanatic
Posts: 196
Joined: Fri Jun 11, 2010 8:46 pm
Location: Scottish Borders

Post by Millar »

Well middle box out would mean no silencers!
Sounds good, did you think it was loud enough when you were there, or even too loud?

Chopped the hole in the bumper for the tailpipes today and ground down some other bits of rust on it, ready for a wee bit filler and primer. But in the process found a ruddy great rusty hole in the corner of the bumper (the seam) so cut it out and treated it with some hammerite anti rust stuff, but it now means i have to go around with this hole until I get a welder :x The new section of pipe were also treated to some vht paint. Talking of paint, I need to find somewhere to buy or mix my paint in to aerosol cans for me, halfords had the instructions for mixing it from the code but didnt have the right colours to mix up, and apparently none of their stores do.
Hennarot 052 if anyone was wondering.
User avatar
e21-Mark
E21 Master
Posts: 5715
Joined: Fri Mar 21, 2008 2:19 pm
My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
Facebook page: https://www.facebook.com/JackyardBackoff
Location: Cornwall - UK

Post by e21-Mark »

Millar wrote:did you think it was loud enough when you were there, or even too loud?
I thought it was spot on.
User avatar
Millar
Upcoming E21 fanatic
Posts: 196
Joined: Fri Jun 11, 2010 8:46 pm
Location: Scottish Borders

Post by Millar »

The clamps and sealant should be here tomorrow, finally! So will get the exhaust finished up.
My mate who's into rat look cars suggested ratting the e21 since its already full of rusty holes, but i'm thinking non of you would approve of that? lol

On another note i was wondering how many bike carbs it would take to run the 320/6 engine? as a stop gap at the moment until i can afford to buy a 2.5 and triple webbers.
User avatar
e21-Mark
E21 Master
Posts: 5715
Joined: Fri Mar 21, 2008 2:19 pm
My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
Facebook page: https://www.facebook.com/JackyardBackoff
Location: Cornwall - UK

Post by e21-Mark »

6 with 0.5 mm mains at a guess.
Last edited by e21-Mark on Tue Jul 06, 2010 11:30 pm, edited 1 time in total.
User avatar
Millar
Upcoming E21 fanatic
Posts: 196
Joined: Fri Jun 11, 2010 8:46 pm
Location: Scottish Borders

Post by Millar »

cheers, certainly the cheapest option i think. anyone on here done it before?
User avatar
Jason_323i
E21 Pro
Posts: 756
Joined: Sun Jan 23, 2005 3:43 pm
Facebook page: https://www.facebook.com/#!/e21jason
Location: Dubai UAE

Post by Jason_323i »

I have triple webber fabricated manifold £125 then eBay for some 40's cheaper than bike carbs

Jason
BMW e21 race car supercharged s14 cage and fabrication by www.chizfab.com
Z3M Coupe
2.8 Z3 Coupe
Caterham Supersport
Clio 172 Cup factory race car(50%)
Ferrari 348 Challenge track car
User avatar
tommi_e21
E21 Mad
Posts: 1536
Joined: Fri May 16, 2008 2:31 am
Location: letchworth sg61hy

Post by tommi_e21 »

my mate joe, who is king in the rat contry loves the idea of ratting a BMW but refuses to let me do it to an e21 saying that it would be a shame and i think i would have to agree.
User avatar
e21-Mark
E21 Master
Posts: 5715
Joined: Fri Mar 21, 2008 2:19 pm
My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
Facebook page: https://www.facebook.com/JackyardBackoff
Location: Cornwall - UK

Post by e21-Mark »

Personally, I think the whole rat thing has been done to death now anyway.
User avatar
Pho21_girl
E21 Pro
Posts: 568
Joined: Sat Oct 24, 2009 7:49 pm
Location: St Albans
Contact:

Post by Pho21_girl »

Don't do it! There are too few cars in good condition, you can't ruin one on purpose lol!
I don't mind rat-look cars, and know a few people with them, but they're VW's...so not such a loss with the numbers of them on the road :lol:
Hannah x
www.hannahdollimore.co.uk
User avatar
Millar
Upcoming E21 fanatic
Posts: 196
Joined: Fri Jun 11, 2010 8:46 pm
Location: Scottish Borders

Post by Millar »

I might well take you up on that Jason. What kind of Webers? Dcoe's?
And as for the rat idea, it was only that, an idea, because of my sheer laziness haha, I could of just left it how it is!
But no, its getting a strip down, all the rust sorted and then a paint job, when i can afford it.
Exhaust almost got finished today, until i took it for a run and found it was making a strange noise, yes the driveshaft was knocking great dents into the pipework! (schoolboy error I know) That should be sorted now, just some finishing touches like making the hole around it a bit bigger so it doesnt rub, then its done.
Here's what it sounds like:

That was it unfinished, and i believe thats steam :)
User avatar
Jason_323i
E21 Pro
Posts: 756
Joined: Sun Jan 23, 2005 3:43 pm
Facebook page: https://www.facebook.com/#!/e21jason
Location: Dubai UAE

Post by Jason_323i »

it is for 40 dcoe's

Jason
BMW e21 race car supercharged s14 cage and fabrication by www.chizfab.com
Z3M Coupe
2.8 Z3 Coupe
Caterham Supersport
Clio 172 Cup factory race car(50%)
Ferrari 348 Challenge track car
User avatar
Millar
Upcoming E21 fanatic
Posts: 196
Joined: Fri Jun 11, 2010 8:46 pm
Location: Scottish Borders

Post by Millar »

sweet yeah i'll probably take that cause it will do for when i upgrade to a 2.5 as well.
Exhaust finished :) taking it for a run tonight with the windows wound down.
Post Reply