Hazard warning light switch - howto on p. 2

PHR 614Y
Newbee
Posts: 8
Joined: Mon Aug 11, 2008 9:05 pm
Location: Norfolk

Post by PHR 614Y »

£30!? I just bought one from BMW for £6.95, bargain!


User avatar
323baur
E21 VIP
E21 VIP
Posts: 11805
Joined: Fri Jan 12, 2007 8:44 pm
Location: the Netherlands, Houten
Contact:

Post by 323baur »

Today, mine was broken, repared as seen on pics - super tip!
(just a little bent is enough!).
Understeer is when you hit the wall with the front of the car and oversteer is when you hit the wall with the rear of the car. Horsepower is how fast you hit the wall. Torque is how far you take the wall with you.
User avatar
jpupster
Newbee
Posts: 19
Joined: Sun Oct 19, 2008 4:10 am
My E21(s): '83 US 320i
Location: Atlanta, GA

Post by jpupster »

Here's a trick. Take small piece of paper fold it 4 or 5 times. With the flasher engaged and blinking, slide the folded paper in the crack around the flasher and push in the flasher, helping the paper into the crack. The paper will act as a wedge and keep the damn thing in the freakin hole. It works, save your money! :D
User avatar
--ALPINA--
E21 Pro
Posts: 1014
Joined: Wed May 17, 2006 1:29 am
Contact:

Post by --ALPINA-- »

yeah we know that dude, thanks for reminding us!! :lol: :lol: :lol: but we have good cars that we would rather be it fully functional.. money isnt an issue when it comes to bits like this, well for me it does as i live on the streets .....


j
(- (- (- ---- Project 911 on the hunt ----) -) -)
User avatar
David Mc
E21 starter
Posts: 23
Joined: Tue Oct 07, 2008 9:58 pm
Location: Queensland Australia
Contact:

Post by David Mc »

I decided to repair my hazard switch permanently, by remanufacturing the alloy arm that seem to be the source of all failures from a piece of 1.5mm thick stainless steel. I carefully removed the rivet then simply copied the arm shape, creating the locating and contact pins by drilling 1mm dia holes and press fitting some 1.2mm pins into the holes.

The whole job took around 1 hour but now I have a virtually bullet-proof switch. :D
User avatar
BillSchroeder
Newbee
Posts: 6
Joined: Mon Oct 01, 2007 5:55 am
Location: Southlake, Texas

Post by BillSchroeder »

30 quid? Sounds expensive. Dude you could have fixed it for free!
Bill Schroeder
'69 Dodge Charger
'80 320iS
'01 325Ci
'08 528i
'08 335Ci
I'm shocked, shocked to find that gambling is going on in here!
Texas Proud
g323
Newbee
Posts: 1
Joined: Mon Dec 29, 2008 5:32 pm

Jumper the switch

Post by g323 »

Hazardous Hazard Switch Jump:


Image

Image

See:
http://forums.bimmerforums.com/forum/sh ... p?t=683955[/img]
User avatar
jirky
E21 starter
Posts: 31
Joined: Tue Mar 10, 2009 5:58 pm
Location: Belgium (Meise)
Contact:

Post by jirky »

Mine's are broken to, bought a new one :) 15 euro's expinsive litle button if you ask me :)
nismo joe
Newbee
Posts: 1
Joined: Sat Mar 07, 2009 4:54 pm
Contact:

Post by nismo joe »

So the jumper from 2 posts above is a proven Bypass from the switch?

If so, I can modify my brothers car untill the new switch arrives :)
User avatar
oldskoolio
E21 starter
Posts: 27
Joined: Fri Jan 16, 2009 9:40 pm
Location: London

Post by oldskoolio »

Fixed mine - had been held in with a matchstick!

Took only 20mins using the write-up and pictures.

Thanks!!!
User avatar
MRE21
Upcoming E21 fanatic
Posts: 119
Joined: Thu Sep 03, 2009 9:19 pm
My E21(s): Audi RSQ3 8U (Previously owned E21 320
Location: Kent

Post by MRE21 »

I tried to repair my switch today but the bloody thing is tricky to fix! The spring is stuck on the metal contact and I can't get it free. I have trimmed the plastic housing and tried to bend the alloy arm but the liitle brass contact inside the housing (at the bottom) gets in the way of the spring and jams? I take it the metal contact should be bent back away from the spring? What in Gods name is it for??? GRRR! I have no patience :evil:
Image

1980 BMW 320/6 OEM (Now sold😥)
2014 Audi RSQ3 8U
User avatar
E21meister
E21 Pro
Posts: 915
Joined: Fri Jul 24, 2009 6:46 pm

Post by E21meister »

Howtoooo... now with updated pics!

Pop the center grill in the dash out, a smaller flat head screw driver seems to help, then push the hazard switch out from the back side.

Image

Image

Use a pocket knife and a screwdriver to gently seperate the two halves.[/i]

Image

seperate slowly & the inner spring will stay near by.

Image

Image

Image

You can see here where the pin on the little metal arm slides in the groove on the opposite half.

Image

This is the pin/arm closer up:

Image

Use a pair of needle nose pliars and bend the arm in a tiny bit so that the pin/arm stay engaged with the corresponding groove.

Image

Then reassemble the pieces and test. No more Bic pen caps stuck in there to keep it turned off...
Image
User avatar
Bimmerman4Ever
Newbee
Posts: 8
Joined: Sun Feb 07, 2010 6:33 pm
Location: Nevada

Post by Bimmerman4Ever »

I appreciate the write up and photos for the jumper.

My car was missing the top button on the hazard switch when I got it and just had some cardboard jammed in it. But it was causing a fuse to blow for my wipers and signals at random times, even when I was driving in heavy rain :shock: .

After the faulty hazard switch caused my stereo (triggered accessory power) to come on in the middle of the night, I pull that stupid thing out and put in the jumper. No more worries and mysterious electrical problems. :wink:
Past BMWs: 80 320i 85 528e 86 325e 88 325e 88 325i vert
89 325ix 93 740iL 95 525i (all 5 spd xcept 88s and iL)

now own a 03 BMW 1150RT
[img]http://lh5.ggpht.com/_9g4el3zvci0/TOSAfGbEqcI/AAAAAAAABDA/0Y-X9H9QrpU/s640/1069455329_Frqpp-O.jpg[/img]
Reck
E21 Pro
Posts: 791
Joined: Mon Mar 29, 2010 12:26 am
My E21(s): 83 316, 1.8 M10, RHD
Location: Manchester, UK

Re: Hazard warning light switch

Post by Reck »

Thanks for re-uploading those pictures meister. Just done this because I've my MOT tomorrow, worked a treat. A couple of things I thought might be helpful;

The book of lies says you need to remove steering wheel/fascia and instrument cluster to remove the switch. You can just prize off the vent on top (held on with a plastic clip in each corner), remove the connecting plug and push out the switch from behind with a screwdriver.

The bit I had most trouble with was prizing the switch apart. The plastic is really soft and bends/tears quite easily. Just be really careful and patient.
User avatar
pistonheader
E21 Fanatic
Posts: 300
Joined: Sat Jul 05, 2008 9:14 pm
Location: Southampton, UK.

Re: Hazard warning light switch

Post by pistonheader »

Reck wrote:Thanks for re-uploading those pictures meister. Just done this because I've my MOT tomorrow, worked a treat. A couple of things I thought might be helpful;

The book of lies says you need to remove steering wheel/fascia and instrument cluster to remove the switch. You can just prize off the vent on top (held on with a plastic clip in each corner), remove the connecting plug and push out the switch from behind with a screwdriver.

The bit I had most trouble with was prizing the switch apart. The plastic is really soft and bends/tears quite easily. Just be really careful and patient.
strange, on my last one the plastic was bloody tough and took some doing! glad you fixed it. for me, it worked for about 3 months, then failed again :( so i replaced it and it's been fine since, touch wood.
Post Reply