320/6 from New Zealand

brockzila
Upcoming E21 fanatic
Posts: 57
Joined: Tue Jan 19, 2016 5:19 am
My E21(s): 320/6 1982,
Location: New Zealand

Re: 320/6 from New Zealand

Post by brockzila »

Got to keep moving forward on a project. Keeps the enthusiasm firing


User avatar
Jeroen
Site Admin
Posts: 29194
Joined: Tue Sep 14, 2004 12:23 pm
My E21(s): '81 323i Baur
Location: The Netherlands
Contact:

Re: 320/6 from New Zealand

Post by Jeroen »

Speaking of moving forward... what's new mate? :wink:
Regards/groeten, Jeroen
brockzila
Upcoming E21 fanatic
Posts: 57
Joined: Tue Jan 19, 2016 5:19 am
My E21(s): 320/6 1982,
Location: New Zealand

Re: 320/6 from New Zealand

Post by brockzila »

Work on the car stalled.
LSD motor and ZF box all got sold.

I have started a business so the big items got sold to buy equipment.

http://vapourblastingnz.co.nz

Makes parts look like new.

That has taken a lot of time. Shed extension, 3 phase power install and large 40cfm compressor in my shed.

This weekend I have a couple of the boys coming over to cut up one of the cars. I think the black 320 is going to give it's life to save the 323. The wife is very keen to see the unneeded car out of the driveway.

The firewall work is massive and will most properly need complete repair certification. Expensive and not needed on the 323.

Will make a good car out of the two.

We can't get the new panels here. Well that's a lie. BMW NZ say they are not available. Can buy from Europe but freight and then the shipping damage is not worth the effort for the larger panels.

So I'm hoping to get back on to the car that is left in the near future. Will be chipping away a little bit at a time.

Still the same plan for the build but now I'm thinking m54b30. Might as well.

I also have a half rollcage and a race seat.

The e24 hubs have been machined to fit the Holden discs. Had to remove 1mm off them as the inner of the disc was slightly smaller. Now I can get discs from any parts store. There are only 3 e24 discs in the country. So have set it up for easy parts replacement at the race track.

I also have a set of 2002 fibreglass flares.

So no real car work to speak of. But lots to get me back to a point where I can start work on the E21 again.

that's my lunch break over, next post will have plAsma cutter and sparks.
User avatar
uwbuurman
E21 VIP
E21 VIP
Posts: 18637
Joined: Fri Jun 12, 2009 4:49 pm
My E21(s): 1978 type 1 323i 5speed dogleg Polaris
Location: Ljouwert

Re: 320/6 from New Zealand

Post by uwbuurman »

Sounds great!!! Got some pics to share?
It's the man next door!

1978 BMW 323i
1980 BMW 528i maior restitutio
1987 BMW 325iA cabriolet
2006 BMW 320d touring High Executive
2015 BMW 320dA touring xDrive High Executive ///Msport
brockzila
Upcoming E21 fanatic
Posts: 57
Joined: Tue Jan 19, 2016 5:19 am
My E21(s): 320/6 1982,
Location: New Zealand

Re: 320/6 from New Zealand

Post by brockzila »

Hello all.

This thread will end here. This black E21 has sacrificed its life to save the 323 that i have.

I will start another thread for the 323 in the near future.

photos or the body to follow.
Post Reply