Wilwood 4 pot fitting - walkthrough
- e21-Mark
- E21 Master
- Posts: 5715
- Joined: Fri Mar 21, 2008 2:19 pm
- My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
- Facebook page: https://www.facebook.com/JackyardBackoff
- Location: Cornwall - UK
-
- E21 VIP
- Posts: 347
- Joined: Thu Feb 28, 2008 11:55 am
- My E21(s): 1981 Bmw 323i manual Ascot Grey
- Location: london
http://www.bmwe21.net/forum/viewtopic.p ... c&start=15RetroBeemer wrote:Sorry - being a bit thick here but which calliper part number do I need for vented 323 fronts please?
....ayds
All Men Truly Die, But Not All Men Have Truly Lived
www.pristinebodyworks.co.uk
www.pristinebodyworks.co.uk
- e21-Mark
- E21 Master
- Posts: 5715
- Joined: Fri Mar 21, 2008 2:19 pm
- My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
- Facebook page: https://www.facebook.com/JackyardBackoff
- Location: Cornwall - UK
I saw that page but which is it out of the part numbers that are listed?
Part Number-------Bore Size-----------Disc Width
120-8729---------1.38" 35.1mm-------.79"-.86" vented
120-8726---------1.38" 35.1mm-------.35"-.50" solid
120-8728---------1.25" 31.8mm-------.79"-.86" vented
120-8725---------1.25" 31.8mm-------.35"-.50" solid
120-8727---------1.00" 25.4mm-------.79"-.86" vented
120-8724---------1.00" 25.4mm-------.35"-.50" solid
Part Number-------Bore Size-----------Disc Width
120-8729---------1.38" 35.1mm-------.79"-.86" vented
120-8726---------1.38" 35.1mm-------.35"-.50" solid
120-8728---------1.25" 31.8mm-------.79"-.86" vented
120-8725---------1.25" 31.8mm-------.35"-.50" solid
120-8727---------1.00" 25.4mm-------.79"-.86" vented
120-8724---------1.00" 25.4mm-------.35"-.50" solid
- cdavie2002
- Upcoming E21 fanatic
- Posts: 161
- Joined: Fri Feb 27, 2009 10:52 pm
- Location: Aberdeen, Scotland
- Jason_323i
- E21 Pro
- Posts: 756
- Joined: Sun Jan 23, 2005 3:43 pm
- Facebook page: https://www.facebook.com/#!/e21jason
- Location: Dubai UAE
- e21-Mark
- E21 Master
- Posts: 5715
- Joined: Fri Mar 21, 2008 2:19 pm
- My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
- Facebook page: https://www.facebook.com/JackyardBackoff
- Location: Cornwall - UK
- cdavie2002
- Upcoming E21 fanatic
- Posts: 161
- Joined: Fri Feb 27, 2009 10:52 pm
- Location: Aberdeen, Scotland
- e21-Mark
- E21 Master
- Posts: 5715
- Joined: Fri Mar 21, 2008 2:19 pm
- My E21(s): 316 m52/2.8 Cat Cams & Jenvey ITB
- Facebook page: https://www.facebook.com/JackyardBackoff
- Location: Cornwall - UK
- cdavie2002
- Upcoming E21 fanatic
- Posts: 161
- Joined: Fri Feb 27, 2009 10:52 pm
- Location: Aberdeen, Scotland
Due to my general busyness and too much to do I got the guys at ric woods to fit my wilwoods while they were sorting out the cracked spring retainer cap and doing my proper mapping. Interestingly they had to machine the pads down a bit as the brakes were binding and the car wouldn't move.
Anyone else had this?
Anyone else had this?
1983 316 Pustergrun - track sluG!
1982 Saphirblau Baur 325i
Cars all gone!
1982 Saphirblau Baur 325i
Cars all gone!
I did have this but I was able to spin the wheel ok. so drove it round the block a couple of times and then they didnt bind anymore! ghetto machining.drjim wrote:Due to my general busyness and too much to do I got the guys at ric woods to fit my wilwoods while they were sorting out the cracked spring retainer cap and doing my proper mapping. Interestingly they had to machine the pads down a bit as the brakes were binding and the car wouldn't move.
Anyone else had this?
- --ALPINA--
- E21 Pro
- Posts: 1014
- Joined: Wed May 17, 2006 1:29 am
- Contact: